How to : How to Thaw a Frozen Pipe

Things You Should Know

Turn your faucets on and look for leaks to narrow down the location of any frozen pipes and help them thaw.
Warm the pipe with a blow dryer and wrap electrical pipe tape around it to thaw a pipe.
Insulate your home and keep the heat on so that it stays at least 55 °F (13 °C) during winter to keep pipes from freezing.
Avoid pouring boiling water or drain cleaners down your drains. These can increase the odds you end up bursting a pipe.

Method 1

Method 1 of 4:

Locating Frozen Pipes

1
Test your faucets to find frozen water pipes. If water runs through all your faucets except one, the dysfunctional faucet is the location of the frozen pipe. If you’re worried about frozen pipes, leave all the working faucets open slightly. A small trickle of running water from working faucets can prevent further freezing and help melt the ice.^{[1]

X

Trustworthy Source
State of Indiana

Official site for state-approved sources related to life in Indiana, including laws, services, and culture
Go to source

Most homes have faucets on external walls too, especially on the front and back of the house.}
2
Presume it’s the pipes in the exterior walls if you have no water. If a large area of your house has no water, look in the most likely and accessible areas first before you start tearing apart walls. Since exterior walls end up bearing most of the cold, that’s the most likely location for frozen pipes. Keep narrowing down the search. Be sure to check:^{[2]

X

Research source

Pipes in or near uninsulated crawlspaces, attics, or basements.
Pipes near cold air vents or cold concrete.
Outdoor valves and spigots.
Outdoor pipes can freeze, but check these last, as most systems are designed to keep standing water out of these pipes.}
3
Search for cracks and leaks to confirm busted pipes. Freezing water can cause pipes to crack from the change in pressure, usually splitting the pipe lengthwise or causing cracks in the joints. If you find an active leak, you’ve located the frozen (and unfortunately broken) pipe.^{[3]

X

Research source

If you find a leak, close the main shut-off valve immediately. Call a plumber to replace the pipe, or fix it yourself if you are up to the task.^{[4]

X

Expert Source

David Balkan
Professional Plumber & CEO of Balkan Sewer & Water Main
Expert Interview. 29 April 2021.}}
4
Feel or tap exposed pipes to confirm which section is frozen. Assuming there are no leaks or cracks, find the section of the pipe with frozen water using one of the following methods.
- Feel the temperature of the pipe with your hand or use an infrared thermometer to locate areas significantly colder than other pipes.
- Tap the pipe with a screwdriver handle or other object, listening for a more solid, less “hollow” sound.
- If you rule out all exposed pipes in the affected area, skip to the section on unfreezing pipes inside walls.

Method 2

Method 2 of 4:

Unfreezing Water Pipes

1
Wait for the pipes to thaw on their own if there’s no rush. If this is a pilot house, vacation home, or you simply aren’t in a rush, just shut off the main water supply and wait it out. Your pipes will eventually thaw as the weather warms up and everything will go back to normal.^{[5]

X

Research source

The main water supply is likely in your basement. Look for the large pipe coming into your home and connecting to your hot water heater. Close the valve on that pipe to shut your home’s water off.}
2
Shut the water off if your faucets produce no water. If you turn a faucet on and nothing comes out, it means at least one of your supply pipes is frozen shut. Turn the water main off to take the pressure off of the frozen pipe. If that pressure keeps building up, you could accidentally burst a pipe.^{[6]

X

Research source

If water does come out of all of your faucets (even just a little), it’s better to leave the water open and run it than it is}
3
Leave the faucet slightly open and let the water run. Open the faucet attached to the frozen pipe, and open nearby working faucets to a trickle. Running water is much less likely to freeze than standing water. If the running water passes through or near a frozen area, it may even help thaw the ice over the course of an hour or two.^{[7]

X

Expert Source

David Balkan
Professional Plumber & CEO of Balkan Sewer & Water Main
Expert Interview. 29 April 2021.

If you see any cracks in any pipe, turn off the main water supply to your house immediately and close all faucets.
How long it takes for a pipe to thaw depends on how much ice is in the pipe, how big the pipe is, and how cold it is outside. Generally speaking, it should take at least a few hours to thaw.}
4
Use a hair dryer or heat gun to slowly thaw the pipe. If the pipe is exposed and you have a section that’s frozen, turn on a hair dryer and run it back and forth along the frozen pipe. Keep it moving and do not place the dryer directly against the pipe, as uneven or sudden heating can rupture the pipe. If your pipes are metal, you can use a more powerful heat gun instead of a hair dryer.^{[8]

X

Research source

PVC pipes can be damaged at temperatures as low as 140 °F (60 °C). Never use a heat gun or anything stronger than a hair dryer.
Outdoor valves often have fiber washers or other non-heat-safe materials inside them. Heat them slowly and cautiously.}
5
Wrap special heat tape around long lengths of frozen pipe. Purchase electrical heat tape designed for frozen pipes. Wrap the tape in a single layer around the length of the frozen pipe, then plug it into a power source. The tape consists of heating elements that warm up when turned on.^{[9]

X

Expert Source

David Balkan
Professional Plumber & CEO of Balkan Sewer & Water Main
Expert Interview. 29 April 2021.

Do not overlap electrical heat tape. Wrap it around the pipe only once or in a spiral pattern.
Do not worry about this damaging your pipes. This kind of tape is designed to keep the pipes safely warm, not so hot they’ll warp or break.}
6
Heat the surrounding air slowly over time. Position space heaters, bare incandescent light bulbs, or heat lamps in the room with the frozen pipe, near the pipe but not touching it. Hang up tarps or blankets to trap the heat in a smaller area, if necessary. For large rooms, use several heat sources to ensure safe, even heating of the pipe.^{[10]

X

Research source

Do not leave any space heaters or heat lamps unattended. They can cause fires if they get knocked over or malfunction.}
7
Wrap the pipe in hot towels to thaw it quickly. Put on rubber gloves, and soak some towels in hot water. Wring them out, then wrap them securely around the frozen section of pipe. Replace with freshly soaked, hot towels every 5–10 minutes until the pipe thaws.^{[11]

X

Research source

Do not leave cold wet towels around the pipes—that’s just going to make the towels freeze onto your pipe.}

Method 3

Method 3 of 4:

Thawing Drain Pipes You Can’t Access

1
Add salt to frozen drains where you can’t reach the pipe. Salt lowers the melting point of ice, causing it to melt at colder temperatures (this is why you salt a sidewalk after heavy snow). Pour a tablespoon (15 mL) of salt down the drain of the frozen pipe, and wait for it to thaw the frozen water in the pipe.^{[12]

X

Research source

You can try dissolving the salt in a 1/2 cup (120 mL) of boiling water first, but adding hot water to frozen ice can burst the pipe. It’s fast if it works, but it’s probably not worth risking it.}
2
Blow a fan heater into outdoor vents. If you can find an external vent, put down a fan heater blowing warm air into the vent. Use a cardboard box or tarp to minimize the amount of heat lost to the surrounding air.^{[13]

X

Research source

Pipes often run alongside ductwork, so forcing warm air into the ducts can quickly thaw any pipes that are nearby.}
3
Turn up the central heating. Crank the heat in the house up 75–80 °F (24–27 °C) and wait 2-3 hours. The radiant heat that fills your home will warm up the walls and ceilings that are concealing your pipes.^{[14]

X

Research source

Open closet and cabinet doors so the warm air circulates as close to the walls as possible.}
4
Cut a hole in the wall to reach pipes at risk of burstng. Unfortunately, this is often necessary to reach a frozen pipe before it bursts. Once you’ve narrowed down the likely area of the problem, use a keyhole saw or utility knife to cut a hole in the wall. Then, use any of the methods in this article to thaw the pipe and deal with the problem.^{[15]

X

Research source

If this is a reoccurring problem, consider installing a cabinet door over the hole instead of fully repairing the wall, for ease of access next time this occurs.}

Method 4

Method 4 of 4:

Preventing Pipes from Freezing

1
Insulate the pipes most likely to freeze. Keep pipes in cold areas wrapped with pipe insulation. If an electrical outlet is nearby, you can keep them wrapped with electrical heat tape and then plug the tape in whenever cold weather arrives.^{[16]

X

Trustworthy Source
State of Indiana

Official site for state-approved sources related to life in Indiana, including laws, services, and culture
Go to source

Don’t use rags or other material to cover the pipes. Only use pipe insulation that’s designed for the task.}
Check your crawlspaces and external walls for holes and repair them to minimize exposure to cold air. Use wind barriers or faucet covers to protect faucets and valves on the exterior of the house.^{[17]

X

Research source}
3
Heat cold and unoccupied areas to avoid freezing temperatures. During cold weather, turn on a 60-watt incandescent light bulb near the area of pipe that previously froze, or just below it. If used to warm crawl spaces and other unsupervised areas, make sure there are no flammable materials kept in the same space.^{[18]

X

Trustworthy Source
State of Michigan

Official website for the State of Michigan
Go to source

Don’t let your house temperature drop below 55 °F (13 °C) if you’re traveling or on vacation.^{[19]

X

Trustworthy Source
State of Indiana

Official site for state-approved sources related to life in Indiana, including laws, services, and culture
Go to source}}
It is much more difficult for pipes to freeze if water is running through them since the water will usually travel through the pipe before it has time to freeze. During sub-freezing weather, keep faucets slightly open to allow a trickle of water.^{[20]

X

Expert Source

David Balkan
Professional Plumber & CEO of Balkan Sewer & Water Main
Expert Interview. 29 April 2021.}

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Never use a torch to heat a frozen pipe. You can destroy the pipe and cause a fire.^{[21]

X

Research source}

Thanks

Helpful
0

Not Helpful
0
Never pour drain cleaner or other chemicals down your frozen pipe, as they can burst the pipe by creating too much gas or heat. A small amount of hot water can be used as a last resort, but even this is risky.^{[22]

X

Research source}

Thanks

Helpful
1

Not Helpful
0

You Might Also Like

[1]

Go to source

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

[17]

[18]

[19]

[20]

[21]

[22]

How to : How to Thaw a Frozen Pipe

Things You Should Know

Steps

Locating Frozen Pipes

Unfreezing Water Pipes

Thawing Drain Pipes You Can’t Access

Preventing Pipes from Freezing

Tips

Warnings

You Might Also Like

EDITOR PICKS

The 5 Most Incredible Body Transformations

Best Upcoming Horror Movies 2016 – 2017 Trailers

Top 10 Incredible Technologies You Can Use

POPULAR POSTS

Top 3 Premier Websites for Stainless Steel Trash Cans (Thùng Rác...

The 5 Most Influential People In The World

Tourism Tech: Can These Apps Help You Explore Your City?

POPULAR CATEGORY